The parts of a skateboard

 A skateboard...

Deck
Most decks are constructed with a six to seven-ply cross-laminated maple wood. Some of them have special materials that help to keep the deck from breaking: such as fiberglass, bamboo, resin, Kevlar, carbon fiber, aluminum, and plastic. Some decks made from maple ply are dyed to create various different coloured ply. Modern decks vary in size, but most are 7 to 10.5 inches wide. Wider decks can be used for greater stability when transition or ramp skating. Skateboard decks are usually between 28 and 33 inches long. The underside of the deck can be printed with a design by the manufacturer, blank, or decorated by any other means. In early 2010 a European Company Gravitis introduced the proprietary asymmetric shape, with decentered twin tips to enhance the rider's stance.

Trucks
Attached to the deck are two metal trucks, which connect to the wheels and deck. The trucks are further composed of two parts. The top part of the truck is screwed to the deck and is called the baseplate, and beneath it is the hanger. The axle runs through the hanger. Between the baseplate and the hanger are bushings, also rubbers or grommets, that provide the cushion mechanism for turning the skateboard. The bushings cushion the truck when it turns. The stiffer the bushings, the more resistant the skateboard is to turning. The softer the bushings, the easier it is to turn. A bolt called a kingpin holds these parts together and fits inside the bushings. Thus by tightening or loosening the kingpin nut, the trucks can be adjusted loosely for better turning and tighter for more stability.

Wheels 
The wheels of a skateboard, usually made of polyurethane, come in many different sizes and shapes to suit different types of skating. Larger sizes like 54–85 mm roll faster, and also move more easily over cracks in pavement. Smaller sizes like 48–54 mm keep the board closer to the ground, require less force to accelerate and produce a lower center of gravity, but also make for a slower top speed. Wheels also are available in a variety of hardnesses usually measured on the Shore durometer "A" scale. Wheels range from the very soft to the very hard. As the A scale stops at 100, any wheels labeled 101A or higher are harder, but do not use the appropriate durometer scale. Some wheel manufacturers now use the "B" or "D" scales, which have a larger and more accurate range of hardness. Modern street skaters prefer smaller wheels (usually 51–54 mm), as small wheels with lighter trucks can make tricks like kickflips and other flip tricks easier by keeping the center of gravity of the skateboard closer to the deck, thus making the deck easier to spin. Street wheels are often quite hard as this allows the wheels to slide easier on waxed surfaces for bluntslides and nose/tailslides.

Grip tape
Grip tape is a sheet paper or fabric with adhesive on one side and a surface similar to fine sand paper on the other. Grip tape is applied to the top surface of a board to allow the rider's feet to grip the surface and help the skater stay on the board while doing tricks. Grip tape is usually black, but is also available in various colors, camo, and even clear. Often times they have designs die-cut to show the color of the board, or to show off the board's company logo.

Bearings
Each skateboard wheel is mounted on its axle via two bearings. With few exceptions, the bearings are the industrial standard "608" size, with a bore of 8 mm, an outer diameter of 22 mm, and a width of 7 mm. These are usually made of steel, though silicon nitride, a high-tech ceramic, is sometimes used. Many skateboard bearings are graded according to the ABEC scale. The scale starts with ABEC1 as the lowest, 3, 5, 7, 9. It is a common misconception that the higher ABECs are better for skateboarding, as the ABEC rating only measures tolerances, which do not necessarily apply to skateboards. The ABEC rating does not determine how fast or how durable a bearing used for skateboarding will be. In particular, the ABEC rating says nothing about how well a bearing handles axial (side-to-side) loads, which are severe in most skateboard applications. Many companies do not show the ABEC rating, such as Bones Bearings, which makes bearings specifically for skateboarding, often marketed as "Skate Rated". Each bearing usually contains 7 steel or ceramic ball bearings, although other configurations are used as well.

Hardware
Mounting hardware is a set of eight 10-32 UNC bolts, usually an Allen or Phillips head, and matching nylon locknuts. They are used to attach the trucks to the board. Some sets have one different colored bolt to show which side is the nose of the skateboard.